 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| HD74LV4066A Quad. Analog Switches / Quad. Multiplexers ADE-205-285 (Z) 1st Edition April 1999 Description The HD74LV4066A handles both analog and digital signals, and enables signals of either type with amplitudes of up to 5.5 V (peak) to be transmitted in either direction (at VCC = 0 V to 5.5 V). Each switch section has its own enable input control (C). A high-level voltage applied to C turns on the associated switch section. Applications include signal gating, chopping, modulation or demodulation (modem), and signal multiplexing for analog-to-digital and digital-to-analog conversion systems. Features * VCC = 2.0 V to 5.5 V operation * All inputs VIH (Max.) = 5.5 V (@VCC = 0 V to 5.5 V) Function Table Control L H Note: H: High level L: Low level Switch OFF ON HD74LV4066A Pin Arrangement 1A 1 1B 2B 2 3 14 VCC 13 1C 12 4C 11 4A 10 4B 9 3B 8 3A 2A 4 2C 3C GND 5 6 7 (Top view) 2 HD74LV4066A Absolute Maximum Ratings Item Supply voltage range Input voltage range* 1 1, 2 Symbol VCC VI VO I IK I OK IO I CC or IGND PT Ratings -0.5 to 7.0 -0.5 to 7.0 -0.5 to VCC + 0.5 -20 50 25 50 785 500 Unit V V V mA mA mA mA mW Conditions Output voltage range* Input clamp current Output clamp current Output: H or L VI < 0 VO < 0 or VO > VCC VO = 0 to VCC Continuous output current Continuous current through VCC or GND Maximum power dissipation at Ta = 25C (in still air)*3 SOP TSSOP Storage temperature Tstg -65 to 150 C Notes: The absolute maximum ratings are values which must not individually be exceeded, and furthermore, no two of which may be realized at the same time.. 1. The input and output voltage ratings may be exceeded even if the input and output clamp-current ratings are observed. 2. This value is limited to 5.5 V maximum. 3. The maximum package power dissipation was calculated using a junction temperature of 150C. Recommended Operating Conditions Item Supply voltage range Input voltage range Output voltage range Input transition rise or fall rate Symbol VCC VI VI/O t/v Min 2.0* 0 0 0 0 0 Operating free-air temperature Ta -40 1 Max 5.5 5.5 VCC 200 100 20 85 Unit V V V ns/V Conditions VCC = 2.3 to 2.7 V VCC = 3.0 to 3.6 V VCC = 4.5 to 5.5 V C Notes: Unused or floating inputs must be held high or low. 1. With the supply voltage at or around 2 V, the analog switch on-state resistance loses linearity significantly. It is recommended that only digital signals be transmitted at these low supply voltages. 3 HD74LV4066A Logic Diagram A B C 4 HD74LV4066A DC Electrical Characteristics Ta = 25C Item Input voltage Symbol VIH VCC (V) 2.0 2.3 to 2.7 3.0 to 3.6 4.5 to 5.5 VIL 2.0 2.3 to 2.7 3.0 to 3.6 4.5 to 5.5 On-state switch resistance RON 2.3 Min -- -- -- -- -- -- -- -- -- Typ -- -- -- -- -- -- -- -- 60 Max -- -- -- -- -- -- -- -- 180 Ta = -40 to 85C Min 1.5 VCC x 0.7 VCC x 0.7 VCC x 0.7 -- -- -- -- -- Max -- -- -- -- 0.5 VCC x 0.3 VCC x 0.3 VCC x 0.3 225 VIN = VCC or GND VC = VIH IT = 1 mA 3.0 4.5 Peak on resistance RON (P) 2.3 -- -- -- 50 40 250 150 75 500 -- -- -- 190 100 600 VIN = VCC to GND VC = VIH IT = 1 mA 3.0 4.5 Difference of on-state resistance between switches RON 2.3 -- -- -- 100 50 20 180 100 30 -- -- -- 225 125 40 VIN = VCC to GND VC = VIH IT = 1 mA Unit V Test Conditions 3.0 4.5 Off-state switch leakage current On-state switch leakage current Input current Quiescent supply current Is (OFF) 5.5 -- -- -- 10 7 -- 20 15 0.1 -- -- -- 30 20 1.0 A VIN = VCC, VOUT = GND or V IN = GND, VO = VCC, VC = VIL VIN = VCC or GND V C = VIH VIN = 5.5 V or GND VIN = VCC or GND Is (ON) 5.5 -- -- 0.1 -- 1.0 A IIN ICC 0 to 5.5 5.5 -- -- -- -- 0.1 -- -- -- 1.0 20 A A Note: For conditions shown as Min or Max use the appropriate values under recommended operating conditions. 5 HD74LV4066A Switching Characteristics * VCC = 2.5 0.2 V Ta = 25C Item Propagation delay time Symbol tPLH tPHL Min -- -- Enable time tZH tZL -- -- Disable time tHZ tLZ -- -- Typ 2.0 5.0 6.0 8.0 7.0 11.0 Max 10.0 12.0 15.0 25.0 15.0 25.0 Ta = -40 to 85C Min -- -- -- -- -- -- Max 16.0 18.0 20.0 32.0 23.0 32.0 ns RL = 1 k ns Unit ns Test Conditions CL = 15 pF CL = 50 pF RL = 1 k CL = 15 pF CL = 50 pF CL = 15 pF CL = 50 pF C A or B C A or B FROM (Input) A or B TO (Output) B or A * VCC = 3.3 0.3 V Ta = 25C Item Propagation delay time Symbol tPLH tPHL Min -- -- Enable time tZH tZL -- -- Disable time tHZ tLZ -- -- Typ 1.5 4.0 4.0 6.0 5.0 8.0 Max 6.0 9.0 11.0 18.0 11.0 18.0 Ta = -40 to 85C Min -- -- -- -- -- -- Max 10.0 12.0 15.0 22.0 15.0 22.0 ns RL = 1 k ns Unit ns Test Conditions CL = 15 pF CL = 50 pF RL = 1 k CL = 15 pF CL = 50 pF CL = 15 pF CL = 50 pF C C FROM (Input) TO (Output) B or A A or B A or B A or B 6 HD74LV4066A Switching Characteristics (cont) * VCC = 5.0 0.5 V Ta = 25C Item Propagation delay time Symbol tPLH tPHL Min -- -- Enable time tZH tZL -- -- Disable time tHZ tLZ -- -- Typ 1.0 3.0 3.0 5.0 4.0 6.0 Max 4.0 6.0 7.0 12.0 7.0 12.0 Ta = -40 to 85C Min -- -- -- -- -- -- Max 7.0 8.0 10.0 16.0 10.0 16.0 ns RL = 1 k ns Unit ns Test Conditions CL = 15 pF CL = 50 pF RL = 1 k CL = 15 pF CL = 50 pF CL = 15 pF CL = 50 pF C A or B C A or B FROM (Input) A or B TO (Output) B or A 7 HD74LV4066A Switching Characteristics (cont) Ta = 25C Item Control input capacitance Switch terminal capacitance Feedthrough capacitance Power dissipation capacitance Frequency response (Switch ON) Symbol CIC CI/O CT CPD VCC (V) -- -- -- -- 2.3 Min -- -- -- -- -- Typ 3.5 6.0 0.5 4.0 30.0 Max -- -- -- -- -- Unit pF pF pF pF MHz CL = 50 pF, RL = 600 Adjust f in voltage to obtain 0 dBm at output when fin is 1 MHz (sine wave). Increase fin frequency until the dB-meter reads -3dBm. 20 log (VO/V I) = -3 dBm A or B B or A Test Conditions FROM (Input) TO (Output) 3.0 4.5 Crosstalk (Between any switches) 2.3 -- -- -- 35.0 50.0 -45.0 -- -- -- dB CL = 50 pF, RL = 600 Adjust f in voltage to obtain 0 dBm at input when fin is 1 MHz (sine wave). A or B B or A 3.0 4.5 Crosstalk (Control input to signal output) 2.3 -- -- -- -45.0 -45.0 15.0 -- -- -- mV CL = 50 pF, RL = 600 Adjust RL value to obtain 0 A at IIN/OUT when fin is 1 MHz (square wave). C A or B 3.0 4.5 -- -- 20.0 50.0 -- -- 8 HD74LV4066A Switching Characteristics (cont) Ta = 25C Item Feedthrough attenuation (Switch OFF) Symbol VCC (V) 2.3 Min -- Typ -40.0 Max -- Unit dB Test Conditions CL = 50 pF, RL = 600 Adjust f in voltage to obtain 0 dBm at input when f in is 1 MHz (sine wave). FROM (Input) A or B TO (Output) B or A 3.0 4.5 Sine-wave distortion 2.3 -- -- -- -40.0 -40.0 0.1 -- -- -- % CL = 50 pF, RL = 10 k fIN = 1 kHz (sine wave) VI = 2 VP-P, VCC = 2.3 V VI = 2.5 VP-P, VCC = 3.0 V VI = 4 VP-P, VCC = 4.5 V A or B B or A 3.0 4.5 -- -- 0.1 0.1 -- -- 9 HD74LV4066A Test Circuits RON: On-state switch resistance VCC VC = VIH VCC VIN = VCC or GND (ON) GND VOUT VIN -VOUT 10 -3 R ON = 1.0 mA V VIN -VOUT () Is (OFF): Off-state switch leakage current, Is (ON): On-state switch leakage current VCC VC = VIL VCC A A (OFF) GND B CONDITION 1: V = 0, VB = VCC A CONDITION 2: V = VCC , V B = 0 A VCC VC = VIH VCC A A (ON) GND B Open VA = VCC or GND 10 HD74LV4066A t PLH, t PHL : Propagation delay time (from switch input to switch output) V CC VC = VIH V CC A RL = 50 (ON) GND B CL = 15 or 50 pF Switching time V CC RL = 50 VC S1 VIN VCC GND RL = VOUT 1 k CL = 15 or 50 pF S2 TEST tLZ /t ZL tHZ /t ZH VCC VC 50% VCC t ZL VOUT 50% VCC VOL 0V VCC VOUT VC S1 GND VCC S2 VCC GND VCC 50% VCC t ZH 50% VCC 0 V 0V VOH VCC VC 50% VCC t LZ VOUT VOL +0.3 V VOL 0V VCC VOUT VC 50% VCC t HZ VOH -0.3 V VCC 0V VOH 0 V 11 HD74LV4066A Frequency response (Switch ON) VCC V C = V IH 0.1 F VIN RL = 50 VCC (ON) GND VOUT RL = 600 VCC /2 CL = 50 pF f in = sine wave f in Crosstalk (Between any switches) VCC V C = V IH 0.1 F RL = 50 RL = 600 VIN VCC (ON) GND VOUT1 RL = 600 VCC /2 VCC V C = V IL VCC RL = 600 VCC /2 (OFF) GND VOUT2 RL = 600 VCC /2 CL = 50 pF CL = 50 pF f in 12 HD74LV4066A Crosstalk (Control input to signal output) VCC RL = 50 VC VCC VOUT RL = 600 VCC /2 Feedthrough attenuation (Switch OFF) VCC VC = VIL 0.1 F RL = 50 VIN RL = 600 VCC /2 V CC (OFF) GND VOUT RL = 600 VCC /2 CL = 50 pF GND RL = 600 VCC /2 CL = 50 pF f in Sine-wave distortion VCC VC = VIH 10 F VIN VCC (ON) GND VOUT RL = 10 k VCC /2 CL = 50 pF f in 13 HD74LV4066A Package Dimensions Unit: mm 10.06 10.5 Max 14 8 5.5 1 7 *0.22 0.05 0.20 0.04 2.20 Max 7.80 - 0.30 1.15 0 - 8 0.70 0.20 + 0.20 1.42 Max 1.27 *0.42 0.08 0.40 0.06 0.12 M Hitachi Code JEDEC EIAJ Weight (reference value) FP-14DA -- Conforms 0.23 g *Dimension including the plating thickness Base material dimension 14 0.10 0.10 0.15 HD74LV4066A Unit: mm 8.65 9.05 Max 14 8 3.95 1 1.75 Max 7 *0.22 0.03 0.20 0.03 0.10 6.10 + 0.30 - 0.635 Max 1.08 0 - 8 0.11 0.14 + 0.04 - 1.27 *0.42 0.08 0.40 0.06 0.67 0.60 + 0.20 - 0.15 0.25 M Hitachi Code JEDEC EIAJ Weight (reference value) FP-14DN Conforms Conforms 0.13 g *Dimension including the plating thickness Base material dimension 15 HD74LV4066A Unit: mm 5.00 5.30 Max 14 8 4.40 1 +0.08 -0.07 7 0.65 1.0 0.13 M 0.83 Max *0.17 0.05 0.15 0.04 6.40 0.20 0 - 8 0.50 0.10 *0.22 0.20 0.06 1.10 Max 0.10 0.07 +0.03 -0.04 *Dimension including the plating thickness Base material dimension Hitachi Code JEDEC EIAJ Weight (reference value) TTP-14D -- -- 0.05 g 16 Cautions 1. Hitachi neither warrants nor grants licenses of any rights of Hitachi's or any third party's patent, copyright, trademark, or other intellectual property rights for information contained in this document. Hitachi bears no responsibility for problems that may arise with third party's rights, including intellectual property rights, in connection with use of the information contained in this document. 2. Products and product specifications may be subject to change without notice. Confirm that you have received the latest product standards or specifications before final design, purchase or use. 3. Hitachi makes every attempt to ensure that its products are of high quality and reliability. However, contact Hitachi's sales office before using the product in an application that demands especially high quality and reliability or where its failure or malfunction may directly threaten human life or cause risk of bodily injury, such as aerospace, aeronautics, nuclear power, combustion control, transportation, traffic, safety equipment or medical equipment for life support. 4. Design your application so that the product is used within the ranges guaranteed by Hitachi particularly for maximum rating, operating supply voltage range, heat radiation characteristics, installation conditions and other characteristics. Hitachi bears no responsibility for failure or damage when used beyond the guaranteed ranges. Even within the guaranteed ranges, consider normally foreseeable failure rates or failure modes in semiconductor devices and employ systemic measures such as failsafes, so that the equipment incorporating Hitachi product does not cause bodily injury, fire or other consequential damage due to operation of the Hitachi product. 5. This product is not designed to be radiation resistant. 6. No one is permitted to reproduce or duplicate, in any form, the whole or part of this document without written approval from Hitachi. 7. Contact Hitachi's sales office for any questions regarding this document or Hitachi semiconductor products. Hitachi, Ltd. Semiconductor & Integrated Circuits. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan Tel: Tokyo (03) 3270-2111 Fax: (03) 3270-5109 URL NorthAmerica : http:semiconductor.hitachi.com/ Europe : http://www.hitachi-eu.com/hel/ecg Asia (Singapore) : http://www.has.hitachi.com.sg/grp3/sicd/index.htm Asia (Taiwan) : http://www.hitachi.com.tw/E/Product/SICD_Frame.htm Asia (HongKong) : http://www.hitachi.com.hk/eng/bo/grp3/index.htm Japan : http://www.hitachi.co.jp/Sicd/indx.htm For further information write to: Hitachi Semiconductor (America) Inc. 179 East Tasman Drive, San Jose,CA 95134 Tel: <1> (408) 433-1990 Fax: <1>(408) 433-0223 Hitachi Europe GmbH Electronic components Group Dornacher Strae 3 D-85622 Feldkirchen, Munich Germany Tel: <49> (89) 9 9180-0 Fax: <49> (89) 9 29 30 00 Hitachi Europe Ltd. Electronic Components Group. Whitebrook Park Lower Cookham Road Maidenhead Berkshire SL6 8YA, United Kingdom Tel: <44> (1628) 585000 Fax: <44> (1628) 778322 Hitachi Asia Pte. Ltd. 16 Collyer Quay #20-00 Hitachi Tower Singapore 049318 Tel: 535-2100 Fax: 535-1533 Hitachi Asia Ltd. Taipei Branch Office 3F, Hung Kuo Building. No.167, Tun-Hwa North Road, Taipei (105) Tel: <886> (2) 2718-3666 Fax: <886> (2) 2718-8180 Hitachi Asia (Hong Kong) Ltd. Group III (Electronic Components) 7/F., North Tower, World Finance Centre, Harbour City, Canton Road, Tsim Sha Tsui, Kowloon, Hong Kong Tel: <852> (2) 735 9218 Fax: <852> (2) 730 0281 Telex: 40815 HITEC HX Copyright ' Hitachi, Ltd., 1999. All rights reserved. Printed in Japan. |
Price & Availability of HD74LV4066A
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |